Wednesday, October 12, 2016
Remote Controlled Submersible Pump Circuit
Remote Controlled Submersible Pump Circuit
The article discusses a simple remote controlled submersible pump circuit which could be simply configured using any standard 2 channel 433MHz remote control modules. The idea was requested by Mr. James Smith
The Request
Hi swagatam , I have read a lot of your post and have implemented them several time.
Now I want a design for switching my submersible single phase motor on and off via remote control.
On the starter there a push button for on and push button for off.
The push button is pushed only for 2 seconds and released and the motor is ON.
The same for stop. The push button is pushed for 2 seconds and the motor is OFF.
Pls help me in doing this as we are having trouble going up and down the staircase from 7 floor to ground floor to just ON and OFF the submersible motor.
If the circuit is ready, I will just connect it to the push buttons.?
James Smith
The Design
We have already witnessed the basic triggering concept of a submersible pump using an automatic "start" and "stop" implementation of the pump contactor switches.
In this remote controlled submersible pump circuit also we follow a similar concept but instead of water sensors, here we do it using a remote controlled modules and subsequent momentary relays switching for initiating the relevant start stop buttons.
For this we can employ a two channel 433 MHz RF remote control modules, which are extremely accurate with their working.
I would recommend buying this unit instead of building one, because these are quite cheap and are easily accessible through online electronic stores.
However if you are interested to make it, you could try it out by procuring the recommended chips for these remote controlled modules which are also available through all standard online electronic retailer.
If you purchase the units readymade, then its just about configuring the relay contacts with the submersible start, and stop buttons, as shown below.
To be precise, its the N/O and the pole of the relays which needs to be connected across the submersible buttons.
For identifying the relay contacts of the remote receiver unit one may take the help of one my earlier pasts which explained how to understand and use relays in circuits.
However since the contactor start stop buttons could be specified to work with high switching current, these may require special high current relay driver stages for the individual buttons.
Therefore the triggering supply from the remote receiver relays needs to be further integrated with the above mentioned high power relay driver stages as demonstrated in the following figure:
The relay driver stages shown at the right side of the diagram is made by configuring transistor relay drivers with the respective high power relays.
The bases of the transistors can be seen connected with series high value capacitors, this is to ensure that the relays remain activated only for a couple of seconds, regardless of the switching periods of the remote control modules relays, or regardless of how long the user keeps the remote transmitter handset button pressed.
The shown remote control receiver module consisting of the receiver circuitry and the two relays will need 12V supply from an appropriate DC source, such as a 12V AC DC adapter.
This 12V further needs to be configured with the relay contacts and the relay driver stages also, for enabling the intended remote controlled start/stop switching of the submersible ON/OFF buttons.
The Request
Hi swagatam , I have read a lot of your post and have implemented them several time.
Now I want a design for switching my submersible single phase motor on and off via remote control.
On the starter there a push button for on and push button for off.
The push button is pushed only for 2 seconds and released and the motor is ON.
The same for stop. The push button is pushed for 2 seconds and the motor is OFF.
Pls help me in doing this as we are having trouble going up and down the staircase from 7 floor to ground floor to just ON and OFF the submersible motor.
If the circuit is ready, I will just connect it to the push buttons.?
James Smith
The Design
We have already witnessed the basic triggering concept of a submersible pump using an automatic "start" and "stop" implementation of the pump contactor switches.
In this remote controlled submersible pump circuit also we follow a similar concept but instead of water sensors, here we do it using a remote controlled modules and subsequent momentary relays switching for initiating the relevant start stop buttons.
For this we can employ a two channel 433 MHz RF remote control modules, which are extremely accurate with their working.
However if you are interested to make it, you could try it out by procuring the recommended chips for these remote controlled modules which are also available through all standard online electronic retailer.
If you purchase the units readymade, then its just about configuring the relay contacts with the submersible start, and stop buttons, as shown below.
To be precise, its the N/O and the pole of the relays which needs to be connected across the submersible buttons.
For identifying the relay contacts of the remote receiver unit one may take the help of one my earlier pasts which explained how to understand and use relays in circuits.
However since the contactor start stop buttons could be specified to work with high switching current, these may require special high current relay driver stages for the individual buttons.
Therefore the triggering supply from the remote receiver relays needs to be further integrated with the above mentioned high power relay driver stages as demonstrated in the following figure:
The relay driver stages shown at the right side of the diagram is made by configuring transistor relay drivers with the respective high power relays.
The bases of the transistors can be seen connected with series high value capacitors, this is to ensure that the relays remain activated only for a couple of seconds, regardless of the switching periods of the remote control modules relays, or regardless of how long the user keeps the remote transmitter handset button pressed.
The shown remote control receiver module consisting of the receiver circuitry and the two relays will need 12V supply from an appropriate DC source, such as a 12V AC DC adapter.
This 12V further needs to be configured with the relay contacts and the relay driver stages also, for enabling the intended remote controlled start/stop switching of the submersible ON/OFF buttons.
Available link for download
