Showing posts with label explained. Show all posts
Showing posts with label explained. Show all posts
Saturday, October 15, 2016
Opamp Hysteresis Explained
Opamp Hysteresis Explained
In most automatic battery charger circuits in this blog you might have seen an opamp with a hysteresis feature included for some crucial function. The following article explains the significance and design techniques for the hysteresis function in opamp circuits.
To learn exactly whats a hysteresis you can refer to this article which explains hysteresis through an example of a relay
Principle of Operation
Figure 2 demonstrates a conventional design for a comparator without employing the hysteresis. This arrangement works by using a voltage divider (Rx and Ry) to establish the minimum threshold voltage.

The comparator would evaluate and compare the input signal or the voltage (Vln) to the set threshold voltage (Vth).
The comparator input feed voltage which is to be compared is connected to the inverting input, as a result the output is going to feature an inverted polarity.
Each time the Vin > Vth the output is supposed to get close to the negative supply (GND or logic low for the shown diagram). and when Vln < Vth the output would get close to the positive supply (Vcc = 5V or logic high in this example).
This easy solution enables you to decide whether or not a genuine signal for example temperature is above a given decisive threshold limit.
Even so, using this technique may possess a predicament. Interference on the input feed signal could potentially cause the input to changeovers above and below the set threshold triggering an inconsistent or fluctuating output results.
Figure 3 illustrates the output response of a comparator without hysteresis with a fluctuating input voltage pattern.

While the input signal voltage arrives the set limit (by the voltage divider network) (Vth = 2.5V), it adjusts above as well as below the minimum threshold a number of instances.
As a result, the output fluctuates too in accordance with the input. In actual circuits, this unstable output may easily cause unfavorable issues.
As an illustration, think about the input signal to be a temperature parameter and the output response to be a crucial temperature based application, which happens to be interpreted by a microcontroller.
The fluctuating output signal response may not contribute a faithful information to the microcontroller and could produce "confusing" results for the microcontroller at the crucial threshold levels.
Additionally, imagine that the comparator output is required to operate a motor or valve. This inconsistent switching during the threshold limits could force the valve or motor to be switched ON/OFF many times in the course of the crucial threshold situations..
But a "cool" solution through a modest alteration to the comparator circuit enables you to include hysteresis which in turn completely eliminates the jittery output during threshold changeovers.
Hysteresis takes advantage of a couple of distinct threshold voltage limits to stay clear from the fluctuating transitions as seen in the discussed circuit.
The input signal feed needs to go over the upper threshold (VH) to generate a changeover of a low output or below the lower set threshold limit (VL) to switch over to a high output.
Figure 4 indicates hysteresis on a comparator. The resistor Rh locks on the hysteresis threshold level.

Each time the output is at a logic high (5V), Rh remains in parallel with Rx. This pushes extra current into Ry, elevating the threshold limit voltage (VH) to 2.7V. The input signal will likely need to go above VH=2.7V to prompt the output response to move to a logic low (0V).
While the output is at logic low (0V), Rh is set parallel with Ry. This cuts-down on the current into Ry, bringing down the threshold voltage to 2.3V. The input signal will want to go below VL=2.3V to settle the output to a logic high (5V).
Figure 5 signifies the output of a comparator with hysteresis with a fluctuating input voltage. The input signal level is supposed to move over the higher threshold limit (VH = 2.7V) for the opamp output to slip down to logic low (0V).

Also, the input signal level needs to move under the Lower threshold for the opamp output to smoothly climb to logic high (5V).
The disturbance in this example may be negligible and therefore may be ignored, thanks to the hysteresis.
But having said this, in cases where the input signal levels were above the hysteresis calculated range (2.7V - 2.3V) could result in generating supplementary fluctuating output transition responses.
To remedy this, the hysteresis range setting is required to be extended sufficiently to dismiss the induced disturbance in the given specific circuit model.
Section 2.1 provides you with a solution for determining components to fix the thresholds in accordance with your selected application demands.
Design of Hysteresis Comparator
Equations (1) and (2) can be of help to decide upon the resistors wished to create the hysteresis threshold voltages VH and VL. A single value (RX) is required to be arbitrarily picked out.
Within this illustration, RX was determined to 100k to help reduce current draw. Rh was computed to be 575k, accordingly the immediate standard value 576k was implemented. The confirmation for Equations (1) and (2) is presented in Appendix A.

Courtesy: Comparator with Hysteresis Reference Design
Available link for download
Labels:
explained,
hysteresis,
opamp
Thursday, September 29, 2016
Timer IC 555 Explained
Timer IC 555 Explained
The post explains the basic pinout details of the timer IC 555, and how to configure the IC in its standard or popular astable, bistable, and monostable circuit modes. The post also details the various formulas for calculating the IC 555 parameters.
By Girish Radhakrishnan
Our hobby world would be less interesting without IC555. It would be one of our first IC to use in electronics. In this article we are going to look back at history of IC555, their 3 operating modes and some of their specifications.
IC555 was introduced in 1971 by a company called Signetics; it was designed by Hans R. Camenzind. It was estimated that about 1 billion units is manufactured every year.
Thats one IC555 for every 7 people in the world. The Signetics Company is owned by Philips Semiconductor. If we look at the internal block diagram of IC555 we can see three 5K ohm resistors connected in series, so we got name as 555 timer. But some hypothesis claims that it was arbitrary.

A standard IC555 consist of 25 transistors, 15 resistors and 2 diodes integrated on a silicon die. There are two versions of the IC available namely military and civilian grade 555 timer.
The NE555 is a civilian grade IC and has operating temperature range of 0 to +70 degree Celsius. The SE555 is military grade IC and has operating temperature range of -55 to +125 degree Celsius.
You will also find the CMOS version of timer known as 7555 and TLC555; these consume less power compared to standard 555 and operate less than 5V.
CMOS version timers consist of MOSFETs rather than bipolar transistor, which is efficient and consume less power.
PIN DIAGRAM:

· Pin 1: Ground or 0V.
· Pin 2: Trigger or input.
· Pin 3: Output.
· Pin 4: Reset.
· Pin 5: Control.
· Pin 6: Threshold.
· Pin 7: Discharge.
· Pin 8: Vcc.
· Bistable or Schmitt trigger
· Monostable or one shot
· Astable
When the IC555 is configured in bistable mode it works as a basic flip-flop. In other words when the input trigger is given, it toggles the output stateON or OFF.
Normally #pin2 and #pin4 are connected to pull-up resistors in this mode of operation.
When the #pin2 is grounded for short duration, the output at #pin3 goes high; to reset the output, #pin4 is momentarily shorted to ground, and then the output goes low.
There is no need for a timing capacitor here, but connecting a capacitor (0.01uF to 0.1uF) across #pin5 and ground is recommended. #pin7 and #pin6 can be left unconnected in this configuration.
Here is a simple bistable circuit:

When the set button is depressed the output goes high and when reset button is depressed the output goes to low state.R1 and R2 may be 10k ohm, the capacitor may be anywhere between the specified value.
Monostable or one-shot pulse generators are widely used in many electronic applications, where a circuit needs to be switched ON for pre-determined time after a trigger. The output pulse width at #pin3 can be determined by using this simple formula:
T=1.1RC
Where
T is the time in Seconds
R is resistance in ohm
C is capacitance in farads
The output pulse falls when the voltage across the capacitor equals to 2/3 of the Vcc. The input trigger between two pulses must be greater than RC time constant.
Here is a simple Monostable circuit:

This is the most commonly used multivibrator or AMV design, and this would be one of our first circuit implemented for IC555 as a hobbyist (remember alternate blinker LED?).
When IC555 configured as astable multivibrator, it gives out continuous rectangular shaped pulses at #pin3.
The frequency and pulse width can be regulated by R1, R2 and C1.The R1 is connected between Vcc and discharge #pin7, R2 is connected between #pin7 and #pin2 and also #pin6. The #pin6 and #pin2 are shorted.
The capacitor is connected between #pin2 and ground.
The frequency for Astable multivibrator can be Calculated by using this formula:
F = 1.44/((R1+R2*2)*C1)
Where,
F is the frequency in Hertz
R1 and R2 is resistors in ohms
C1 is capacitor in farads.
The high time for each pulse given by:
High= 0.693(R1+R2)*C
Low time is given by:
Low= 0.693*R2*C
All R is in ohms and C is in ohms.
Here is a basic astable multivibrator circuit:

For 555 IC timers with bipolar transistors, R1 with low value must be avoided so that the output stays saturated near ground voltage during discharge process, else the low time could be unreliable and we may see greater values for low time practically than calculated value.
If you want the output less than 50% duty cycle i.e. shorter high time and longer low time, a diode can be connected across R2 with cathode on the capacitor side. Its also called the PWM mode for the 555 IC timer.

You can also design a 555 PWM circuit with variable duty cycle two diodes as shown in the above figure.
By Girish Radhakrishnan
Our hobby world would be less interesting without IC555. It would be one of our first IC to use in electronics. In this article we are going to look back at history of IC555, their 3 operating modes and some of their specifications.
IC555 was introduced in 1971 by a company called Signetics; it was designed by Hans R. Camenzind. It was estimated that about 1 billion units is manufactured every year.
Thats one IC555 for every 7 people in the world. The Signetics Company is owned by Philips Semiconductor. If we look at the internal block diagram of IC555 we can see three 5K ohm resistors connected in series, so we got name as 555 timer. But some hypothesis claims that it was arbitrary.
Internal block diagram:

A standard IC555 consist of 25 transistors, 15 resistors and 2 diodes integrated on a silicon die. There are two versions of the IC available namely military and civilian grade 555 timer.
The NE555 is a civilian grade IC and has operating temperature range of 0 to +70 degree Celsius. The SE555 is military grade IC and has operating temperature range of -55 to +125 degree Celsius.
You will also find the CMOS version of timer known as 7555 and TLC555; these consume less power compared to standard 555 and operate less than 5V.
CMOS version timers consist of MOSFETs rather than bipolar transistor, which is efficient and consume less power.
PIN DIAGRAM:

· Pin 1: Ground or 0V.
· Pin 2: Trigger or input.
· Pin 3: Output.
· Pin 4: Reset.
· Pin 5: Control.
· Pin 6: Threshold.
· Pin 7: Discharge.
· Pin 8: Vcc.
3 Modes of timer:
· Bistable or Schmitt trigger
· Monostable or one shot
· Astable
Bistable Mode:
When the IC555 is configured in bistable mode it works as a basic flip-flop. In other words when the input trigger is given, it toggles the output stateON or OFF.
Normally #pin2 and #pin4 are connected to pull-up resistors in this mode of operation.
When the #pin2 is grounded for short duration, the output at #pin3 goes high; to reset the output, #pin4 is momentarily shorted to ground, and then the output goes low.
There is no need for a timing capacitor here, but connecting a capacitor (0.01uF to 0.1uF) across #pin5 and ground is recommended. #pin7 and #pin6 can be left unconnected in this configuration.
Here is a simple bistable circuit:

When the set button is depressed the output goes high and when reset button is depressed the output goes to low state.R1 and R2 may be 10k ohm, the capacitor may be anywhere between the specified value.
Monostable Mode:
Monostable or one-shot pulse generators are widely used in many electronic applications, where a circuit needs to be switched ON for pre-determined time after a trigger. The output pulse width at #pin3 can be determined by using this simple formula:
T=1.1RC
Where
T is the time in Seconds
R is resistance in ohm
C is capacitance in farads
The output pulse falls when the voltage across the capacitor equals to 2/3 of the Vcc. The input trigger between two pulses must be greater than RC time constant.
Here is a simple Monostable circuit:

Astable Mode:
This is the most commonly used multivibrator or AMV design, and this would be one of our first circuit implemented for IC555 as a hobbyist (remember alternate blinker LED?).
When IC555 configured as astable multivibrator, it gives out continuous rectangular shaped pulses at #pin3.
The frequency and pulse width can be regulated by R1, R2 and C1.The R1 is connected between Vcc and discharge #pin7, R2 is connected between #pin7 and #pin2 and also #pin6. The #pin6 and #pin2 are shorted.
The capacitor is connected between #pin2 and ground.
The frequency for Astable multivibrator can be Calculated by using this formula:
F = 1.44/((R1+R2*2)*C1)
Where,
F is the frequency in Hertz
R1 and R2 is resistors in ohms
C1 is capacitor in farads.
The high time for each pulse given by:
High= 0.693(R1+R2)*C
Low time is given by:
Low= 0.693*R2*C
All R is in ohms and C is in ohms.
Here is a basic astable multivibrator circuit:

For 555 IC timers with bipolar transistors, R1 with low value must be avoided so that the output stays saturated near ground voltage during discharge process, else the low time could be unreliable and we may see greater values for low time practically than calculated value.
If you want the output less than 50% duty cycle i.e. shorter high time and longer low time, a diode can be connected across R2 with cathode on the capacitor side. Its also called the PWM mode for the 555 IC timer.
You can also design a 555 PWM circuit with variable duty cycle two diodes as shown in the above figure.
Available link for download
Friday, August 26, 2016
Nigeria currency crisis explained What we know and don’t know
Nigeria currency crisis explained What we know and don’t know
This article was written by Paul Wallace
Nigerias central bank may soon give bond and stock investors what they have been pleading for: a weaker naira.
Governor Godwin Emefiele announced after a meeting of the Monetary Policy Committee in Abuja, the capital, on Tuesday that a more flexible foreign-exchange system would be unveiled in the coming days. But his statement was short on details and left plenty of questions. Here are some answers:
Whats the problem?
Nigeria has held the naira at 197-199 per dollar since March 2015, even as other oil exporters from Russia to Colombia and Malaysia let their currencies drop amid the slump in crude prices since mid-2014. Foreign reserves dwindled as the central bank defended the peg, while foreign investors, fearing a devaluation, sold Nigerian stocks and bonds.
While President Muhammadu Buhari and Emefiele argued a devaluation would fuel inflation, that happened anyway. Consumer prices accelerated at the fastest pace in six years in April as the black-market naira rate plummeted to about 350 against the dollar. To make matters worse, data released four days before the MPC meeting showed the economy contracted in the first quarter for the first time since 2004 as the dollar shortage curtailed manufacturing.
That probably surprised policy makers, prompting the change of heart, according to Mathias Althoff, a fund manager in Stockholm at Tundra Fonder AB, which has about $200 million invested in frontier market stocks, including Nigerian banks.
What happens next?
While Emefiele didnt specify what he meant by greater flexibility, analysts at Renaissance Capital Ltd. predict the central bank will allocate dollars at a fixed rate to strategic industries, such as energy and agriculture, while letting the naira weaken in the interbank market, where everyone else would buy their foreign currency.
The central bank may also try try to control the new interbank rate by imposing a trading band of about 5 or 10 percent around it, according to Althoff.
Will that satisfy investors and save the economy?
If the central bank doesnt allow the naira to drop enough, foreign investors will continue to shun Nigerian assets, according to Althoff. The currency should trade at around 285-290 per dollar, according to Alan Cameron, an economist at Exotix Partners LLP in London.
A devaluation wont solve Nigerias structural economic problems, which include an over-reliance on oil exports, and may fuel inflation in the short term. But it would make Nigerian exports more competitive, curb imports and encourage foreign investment.
What are the pitfalls?
Most investors would prefer a fully-floating naira, yet doubt that Nigeria, which has always had currency controls of some sort, will choose that option. And there are concerns it will be impossible for the central bank to ensure that only importers meeting its criteria are able to buy foreign currency at the discounted official rate.
Many analysts fear that in a nation U.K. Prime Minister David Cameron described as fantastically corrupt, access to the official rate will come down to political connections.
The suggestion of a dual exchange rate, with the maintenance of the official window, is a concern, said Razia Khan, head of African research at Standard Chartered Plc in London. This might lead to continued distortions in the market, ultimately with pressure on foreign-exchange reserves.
What else should investors watch out for?
Buhari. He has made it clear that he, not Emefiele, is the person in charge of exchange-rate policy. The president is loath to allow the currency to drop unless hes forced to and in February likened such a move to murder. He has yet to make any response to the MPCs announcement.
And while he is due to make a speech on May 29, the first anniversary of his coming to power, local press reports suggest he will focus on the governments fight against corruption and Boko Harams Islamist insurgency.
ALSO READ: How to fix earpiece on Andriod n Upgrade
The central bank has hinted at change before, only to do nothing. The MPC has dangled the carrot of exchange-rate reform, but without giving any details of what a reformed market would look like, said Cameron at Exotix.
To the skeptics among us, this will simply sound like a re-hash of the same old material weve been hearing about since December 2015.
Available link for download
Sunday, August 21, 2016
Raspberry Pi Explained
Raspberry Pi Explained
In this article we are going to learn about Raspberry Pi single board computer, their specifications, how to use them in a project, we are also going to do a small comparison between Arduino and Raspberry Pi, so that we can choose which of them are best for your projects.
By: Girish Radhakrishnan
In other words, it is a full fledged computer, fabricated on a single PCB which is not bigger than your credit card size.
It supports various Linux based operating system (OS) such as Raspbian OS which is official operating system, Ubuntu, windows 10 IoT (which is dedicated for internet of thing projects) , Kali Linux which made for security analysts and white hats. There are several other custom made OS made by third parties for specific projects such as Bitcoin mining and CCTV based projects.

The biggest selling point of Raspberry Pi is price.
You can pick one for $35 or less than 2500 INR on E-commerce sites.
We are getting computing power equivalent to Pentium processors which was released on late 2000s. But it consumes power 100 times less and sits on a single PCB, thanks to Moors law.
After a huge success, Chinese electronic vendors started manufacturing similar single board computers, the popular ones are Banana Pi, Orange Pi, and Roseapple Pi etc; by the way the names can get ridiculous.
These single board computers function similar as raspberry Pi, but some has more functionality and some has less functionality than Raspberry Pi. However Raspberry Pi has the most project support around world.
It sports Broadcom BCM2837 ARM cortex-A53 quad core processor clocked at 1.2GHz; it has dedicated graphics support similar to GPU on computers: Broadcom VideoCore IV. This GPU supports 1080p video play back.
It is coupled with 1 GB of LPDDR2 Ram clocked at 900MHz.
It has on-board Bluetooth (4.1 Low Energy) and Wi-Fi 2.4 GHz band. It has no antenna extended out of the board, which is an advantage when your raspberry pi is inside its case. However it should have decent Bluetooth and Wi-Fi range.
It has a 10/100 Ethernet port, if you dont have Wi-Fi, you can utilize the RJ-45 Ethernet cable from your router to Ethernet port of the raspberry pi.
It has 40 general purpose input output pins or GPIO pins. These pins can be utilizes for controlling external hardware. This means it works as arduino.
It has 3.5mm audio jack, this can be hooked to a headphone or speakers for audio playback.
It has camera serial interface port or CSI port in which you can plug camera modules and can record video up to 1080p resolution.
It has display port on the PCB in which you can hookup LCD displays or even touch screen displays to make your project portable.
It has full HDMI or High definition Multimedia Interface which supports in which you can connect monitor or TV and it support 1080p video play back.
It does not have build-in storage but, it has micro SD card slot in which the OS need to be installed.
It has 4 USB-2.0 ports. You can connect keyboard, mouse, flash drives even external hard disks.
So, thats look impressive for a computer which does not bomb on your bank and great tool for learning programming languages and making electronic projects.
What can we do with Raspberry Pi?
Here I am going to show some projects which are just fraction of the actual capability of raspberry PI.
There are lots and lots of project available around the internet and you can also use your imagination to create your own projects.
Full Linux computer:
This was my very first project, based on raspberry pi. I have used it for learning programming languages, and also to upload programs to arduino.
Yes, you can upload sketch to arduino using raspberry pi.
You can also watch movies for long hours without burning you purse for electric bill, as it consumes less than 5 Watt and the whole setup consumes less than 15 Watt. You can also use it for word processing, web browsing and reading e-mails.


NAS Server:
Here is another project based on raspberry pi: NAS server. In a nutshell NAS stands for network attached storage and it is used as private cloud storage at your home.
You can stream videos files, audio files, and open documents over Wi-Fi to your laptop, tablet, Smartphone.

I am using this NAS also as torrent file downloader (legally, LOL) for downloading huge files with minimum power, so that I do not need to run my main computer overnight, which could only raise the electricity bill.
As you can see, this small computer has huge potentials. Once you get familiar with this single board computer you can do wonders.
Raspberry Pi vs. Arduino:
Lot of people get confused between arduino and raspberry pi while choosing their project. But they must understand that arduino and raspberry pi has nothing to do with each other.
Both are completely different concepts, arduino is purely used for controlling hardware peripherals such as LED, motors, relay, etc. The programs written for Arduino are from single software Arduino IDE and complied to machine language before uploading the code.
Raspberry Pi also has GPIO pins as arduino does, but this doesnt mean that you should use raspberry pi for blinking an LED or Traffic lights control projects. This could be rather done with arduino with much ease and cheaply.
Raspberry Pi runs its program within an operating system through programs written with general purpose languages such as python.
Raspberry Pi should be used where we need to process huge data; projects such as 3D printer, CCTV, Web servers, NAS servers etc, and these tasks cant be accomplished with arduino.
So, choose wisely for your project and dont waste money for accomplishing simple tasks.
If you are interested to learn more about Raspberry Pi, do not hesitate to express your thoughts through comment below:
By: Girish Radhakrishnan
What is Raspberry Pi?
Raspberry Pi is a single board computer, which consists of Microprocessor, Ram, Graphics support, audio support, HDMI support, GPIO support on a single printed circuit board (PCB).In other words, it is a full fledged computer, fabricated on a single PCB which is not bigger than your credit card size.
It supports various Linux based operating system (OS) such as Raspbian OS which is official operating system, Ubuntu, windows 10 IoT (which is dedicated for internet of thing projects) , Kali Linux which made for security analysts and white hats. There are several other custom made OS made by third parties for specific projects such as Bitcoin mining and CCTV based projects.

The biggest selling point of Raspberry Pi is price.
You can pick one for $35 or less than 2500 INR on E-commerce sites.
We are getting computing power equivalent to Pentium processors which was released on late 2000s. But it consumes power 100 times less and sits on a single PCB, thanks to Moors law.
After a huge success, Chinese electronic vendors started manufacturing similar single board computers, the popular ones are Banana Pi, Orange Pi, and Roseapple Pi etc; by the way the names can get ridiculous.
These single board computers function similar as raspberry Pi, but some has more functionality and some has less functionality than Raspberry Pi. However Raspberry Pi has the most project support around world.
Specifications:
Now the things get exciting because you can find similar specification on a decent smart phone or a computer 7 to 10 years back. The given specifications are of raspberry Pi 3 are. It sports Broadcom BCM2837 ARM cortex-A53 quad core processor clocked at 1.2GHz; it has dedicated graphics support similar to GPU on computers: Broadcom VideoCore IV. This GPU supports 1080p video play back.
It is coupled with 1 GB of LPDDR2 Ram clocked at 900MHz.
It has on-board Bluetooth (4.1 Low Energy) and Wi-Fi 2.4 GHz band. It has no antenna extended out of the board, which is an advantage when your raspberry pi is inside its case. However it should have decent Bluetooth and Wi-Fi range.
It has a 10/100 Ethernet port, if you dont have Wi-Fi, you can utilize the RJ-45 Ethernet cable from your router to Ethernet port of the raspberry pi.
It has 40 general purpose input output pins or GPIO pins. These pins can be utilizes for controlling external hardware. This means it works as arduino.
It has 3.5mm audio jack, this can be hooked to a headphone or speakers for audio playback.
It has camera serial interface port or CSI port in which you can plug camera modules and can record video up to 1080p resolution.
It has display port on the PCB in which you can hookup LCD displays or even touch screen displays to make your project portable.
It has full HDMI or High definition Multimedia Interface which supports in which you can connect monitor or TV and it support 1080p video play back.
It does not have build-in storage but, it has micro SD card slot in which the OS need to be installed.
It has 4 USB-2.0 ports. You can connect keyboard, mouse, flash drives even external hard disks.
So, thats look impressive for a computer which does not bomb on your bank and great tool for learning programming languages and making electronic projects.
What can we do with Raspberry Pi?
Here I am going to show some projects which are just fraction of the actual capability of raspberry PI.
There are lots and lots of project available around the internet and you can also use your imagination to create your own projects.
Full Linux computer:
This was my very first project, based on raspberry pi. I have used it for learning programming languages, and also to upload programs to arduino.
Yes, you can upload sketch to arduino using raspberry pi.
You can also watch movies for long hours without burning you purse for electric bill, as it consumes less than 5 Watt and the whole setup consumes less than 15 Watt. You can also use it for word processing, web browsing and reading e-mails.


NAS Server:
Here is another project based on raspberry pi: NAS server. In a nutshell NAS stands for network attached storage and it is used as private cloud storage at your home.
You can stream videos files, audio files, and open documents over Wi-Fi to your laptop, tablet, Smartphone.

I am using this NAS also as torrent file downloader (legally, LOL) for downloading huge files with minimum power, so that I do not need to run my main computer overnight, which could only raise the electricity bill.
As you can see, this small computer has huge potentials. Once you get familiar with this single board computer you can do wonders.
Raspberry Pi vs. Arduino:
Lot of people get confused between arduino and raspberry pi while choosing their project. But they must understand that arduino and raspberry pi has nothing to do with each other.
Both are completely different concepts, arduino is purely used for controlling hardware peripherals such as LED, motors, relay, etc. The programs written for Arduino are from single software Arduino IDE and complied to machine language before uploading the code.
Raspberry Pi also has GPIO pins as arduino does, but this doesnt mean that you should use raspberry pi for blinking an LED or Traffic lights control projects. This could be rather done with arduino with much ease and cheaply.
Raspberry Pi runs its program within an operating system through programs written with general purpose languages such as python.
Raspberry Pi should be used where we need to process huge data; projects such as 3D printer, CCTV, Web servers, NAS servers etc, and these tasks cant be accomplished with arduino.
So, choose wisely for your project and dont waste money for accomplishing simple tasks.
If you are interested to learn more about Raspberry Pi, do not hesitate to express your thoughts through comment below:
Available link for download
Monday, August 15, 2016
Types of Capacitors Explained
Types of Capacitors Explained
In this post we learn regarding the basics of capacitor, and also regarding the various types of capacitors which are commonly available in the market and used in most electronic circuits.
By: S. Prakash.
The performance parameters of every capacitor are different and thus their applications also differ accordingly.
One of the electronic components forms which is used widely is the electronic capacitors. Apart from this, the other capacitors used in the industry include ceramic, silver mica, electrolytic, plastic, tantalum, and others.
Each type of the capacitor is used in various applications according to their respective disadvantages and advantages.
It is quintessential that the right type of capacitor must be selected as the circuit in which the capacitor is used is greatly by the capacitor.
Thus, in case a correct type of capacitor is not selected to insert in the circuit on the basis of its parameters, it can result in the improper or faulty functioning of the circuit.
The physical laws which basically govern the various types of capacitors are same and are adhered to accordingly.
These basic laws determine various parameters of the capacitors such as how the capacitor would operate, the value of the capacitor, and its capacitance (the maximum amount of charge which the capacitor will hold).
Thus, the basic theory on which capacitors are built and work enables to understand the different capacitors forms and how these can be or are used.
Note: Even though there have been numerous developments in the field of dielectrics, the basic laws on which the capacitors work has not changed and they apply to date.
As discussed above, although the basic laws on which the capacitors work, the properties of the capacitors differ enormously because of the manner in which each type of the capacitor is constructed.
The various properties which various types of capacitors possess is given by their main element which is located between the two plates of the capacitor and is known as dielectric.
The dielectric constant of the capacitor can impact the capacitance level which the capacitor can achieve at a given specific volume. Also, various capacitors of different types can be found to be polarized in nature wherein the voltage running across the capacitor is tolerated in one single direction only.
On the other hand, various capacitors of different types can be found to be non-polarized in nature wherein the voltage running across the capacitor is tolerated in both the direction.
The capacitors are commonly named on the basis of the nature of the dielectric which is present in the capacitor.
This is indicative of the general properties which the capacitor will be exhibiting along with the various different types of circuit functions where they can be used.
The various types of capacitors which are being used are as follows:
The capacitor namely, ceramic capacitor is used for multiple applications including RF and audio.
The range of the values of the ceramic capacitor is between few picofarads and 0.1 microfarads. The ceramic capacitors are the most widely used in the industry since it the most reliable and cheap type of capacitor available.
Also, another reason for its common and wide usage is that the loss factor of the ceramic capacitor is very low. But the loss factor of the capacitor is also dependent on the dielectric which is used in the capacitor.
The ceramic capacitors are used in both the formats of surface mount and leaded because of the constructional properties of the capacitors.

One type of capacitor which is polarized in nature is electrolytic capacitors.
The capacitance values which are offered by the electrolytic capacitor is very high which ranges more than 1µF. the electrolytic capacitors are used in the industry commonly for the applications which are conducted on low frequency such as decoupling applications, power supplies, and applications of audio coupling.
This is because these applications have the frequency limit of nearly 100 kHz.

Another type of capacitor which is polarized in nature is tantalum capacitor. The capacitance level provided by the tantalum capacitor at their volume is very high.
One of the drawbacks of the tantalum capacitor is that there is no tolerance in the tantalum capacitor towards reverse biasing which can result in the explosion of the capacitor when exposed to stress.
Another drawback is that it has very low tolerance to the ripple currents and thus they should not be exposed to high voltages (such as voltages which is higher than their working voltage) and high ripple current. The tantalum capacitors are available in both the formats of surface mount and leaded.

Although the usage of the silver mica capacitors have decreased significantly in the current era, the stability provided by the silver mica capacitors are still very high along with providing high accuracy and low loss.
Also, there is sufficient space available in the silver mica capacitors. The applications where they are primarily used include the RF applications.
The maximum values to which the silver mica capacitor is limited to is approximately 100pF.
The polystyrene film capacitors provide capacitor of close tolerance wherever required. Also, these capacitors are relatively cheaper than that of other capacitors.
The dielectric sandwich or the plates present in the polystyrene film capacitors are rolled together which results in the shape of the capacitor in tubular form.
The placement of the dielectric sandwich and shape of the capacitor limits the response of the capacitor to high frequencies due to addition of inductance and thus responds to only few 100kHz.
The general availability of the polystyrene film capacitors is in the form of leaded electronics components.

The tolerance provided by the polyester film capacitor is very low and thereby these capacitors are used in situations when the prior consideration is the cost.
The tolerance level of a large percentage of the polyester film capacitors available is either 10% or 5% and this is considered as sufficient for a range of applications.
The general availability of the polyester film capacitors is in the form of leaded electronics components.

The metallized polyester film type of capacitors consists of polyester films which are metallized and in every other sense, it is similar to the polyester film capacitors or another form of it.
One of the advantages which is achieved by metallic polyester film is that it makes the electrodes of very small width and thereby enabling the encasement of the capacitor in a package of very small sizes as well.
The general availability of the metallized polyester film capacitors is in the form of leaded electronics components.



The other names by which the supercap is known are ultracapacitor or supercapacitor.
The capacitance values of these capacitors are very large as such is their name. The capacitance levels of the ultracapacitor go nearly towards many thousand Farads.
The ultracapacitor is used in the industry for providing a supply of memory hold-up along with various uses within the realm of automotive applications. The different major types of the capacitors are included under the supercap.
Along with them, there are various other capacitor types of capacitors which are used when the applications are specialized in nature.
The identification of the capacitors is majorly done through their parameters such as values which are marked over the cases of the capacitors. In order to display the parameters in a manner which is compact, the markings of the parameters are done in the form of a code.
By: S. Prakash.
The performance parameters of every capacitor are different and thus their applications also differ accordingly.
One of the electronic components forms which is used widely is the electronic capacitors. Apart from this, the other capacitors used in the industry include ceramic, silver mica, electrolytic, plastic, tantalum, and others.
Each type of the capacitor is used in various applications according to their respective disadvantages and advantages.
It is quintessential that the right type of capacitor must be selected as the circuit in which the capacitor is used is greatly by the capacitor.
Thus, in case a correct type of capacitor is not selected to insert in the circuit on the basis of its parameters, it can result in the improper or faulty functioning of the circuit.
Basics of the capacitors
The physical laws which basically govern the various types of capacitors are same and are adhered to accordingly.
These basic laws determine various parameters of the capacitors such as how the capacitor would operate, the value of the capacitor, and its capacitance (the maximum amount of charge which the capacitor will hold).
Thus, the basic theory on which capacitors are built and work enables to understand the different capacitors forms and how these can be or are used.
Note: Even though there have been numerous developments in the field of dielectrics, the basic laws on which the capacitors work has not changed and they apply to date.
Types of Capacitors and Dielectrics
As discussed above, although the basic laws on which the capacitors work, the properties of the capacitors differ enormously because of the manner in which each type of the capacitor is constructed.
The various properties which various types of capacitors possess is given by their main element which is located between the two plates of the capacitor and is known as dielectric.
The dielectric constant of the capacitor can impact the capacitance level which the capacitor can achieve at a given specific volume. Also, various capacitors of different types can be found to be polarized in nature wherein the voltage running across the capacitor is tolerated in one single direction only.
On the other hand, various capacitors of different types can be found to be non-polarized in nature wherein the voltage running across the capacitor is tolerated in both the direction.
The capacitors are commonly named on the basis of the nature of the dielectric which is present in the capacitor.
This is indicative of the general properties which the capacitor will be exhibiting along with the various different types of circuit functions where they can be used.
Overview of capacitors and its different types
The various types of capacitors which are being used are as follows:
Ceramic Capacitor:

The range of the values of the ceramic capacitor is between few picofarads and 0.1 microfarads. The ceramic capacitors are the most widely used in the industry since it the most reliable and cheap type of capacitor available.
Also, another reason for its common and wide usage is that the loss factor of the ceramic capacitor is very low. But the loss factor of the capacitor is also dependent on the dielectric which is used in the capacitor.
The ceramic capacitors are used in both the formats of surface mount and leaded because of the constructional properties of the capacitors.
Electrolytic Capacitor:

One type of capacitor which is polarized in nature is electrolytic capacitors.
The capacitance values which are offered by the electrolytic capacitor is very high which ranges more than 1µF. the electrolytic capacitors are used in the industry commonly for the applications which are conducted on low frequency such as decoupling applications, power supplies, and applications of audio coupling.
This is because these applications have the frequency limit of nearly 100 kHz.
Tantalum Capacitor:

Another type of capacitor which is polarized in nature is tantalum capacitor. The capacitance level provided by the tantalum capacitor at their volume is very high.
One of the drawbacks of the tantalum capacitor is that there is no tolerance in the tantalum capacitor towards reverse biasing which can result in the explosion of the capacitor when exposed to stress.
Another drawback is that it has very low tolerance to the ripple currents and thus they should not be exposed to high voltages (such as voltages which is higher than their working voltage) and high ripple current. The tantalum capacitors are available in both the formats of surface mount and leaded.
Silver Mica Capacitor:

Although the usage of the silver mica capacitors have decreased significantly in the current era, the stability provided by the silver mica capacitors are still very high along with providing high accuracy and low loss.
Also, there is sufficient space available in the silver mica capacitors. The applications where they are primarily used include the RF applications.
The maximum values to which the silver mica capacitor is limited to is approximately 100pF.
Polystyrene Film Capacitor:

The polystyrene film capacitors provide capacitor of close tolerance wherever required. Also, these capacitors are relatively cheaper than that of other capacitors.
The dielectric sandwich or the plates present in the polystyrene film capacitors are rolled together which results in the shape of the capacitor in tubular form.
The placement of the dielectric sandwich and shape of the capacitor limits the response of the capacitor to high frequencies due to addition of inductance and thus responds to only few 100kHz.
The general availability of the polystyrene film capacitors is in the form of leaded electronics components.
Polyester Film Capacitor:

The tolerance provided by the polyester film capacitor is very low and thereby these capacitors are used in situations when the prior consideration is the cost.
The tolerance level of a large percentage of the polyester film capacitors available is either 10% or 5% and this is considered as sufficient for a range of applications.
The general availability of the polyester film capacitors is in the form of leaded electronics components.
Metallized Polyester Film Capacitor

The metallized polyester film type of capacitors consists of polyester films which are metallized and in every other sense, it is similar to the polyester film capacitors or another form of it.
One of the advantages which is achieved by metallic polyester film is that it makes the electrodes of very small width and thereby enabling the encasement of the capacitor in a package of very small sizes as well.
The general availability of the metallized polyester film capacitors is in the form of leaded electronics components.
Polycarbonate capacitor:

The applications where the most critical and crucial requirement is high performance and reliability, these applications use the polycarbonate capacitors.
The capacitance value is held over a long period of time by the polycarbonate capacitors since their tolerance level is very high. Such high tolerance levels are achieved because of the stability of the polycarbonate film used in the polycarbonate capacitor.
Additionally, the dissipation factor of the polycarbonate capacitor is very low and they can withstand temperature of wide range and remain stable. The range of temperature which this capacitor can withstand is between -55ºC and +125ºC. In spite of all these properties, the manufacturing and production of the polycarbonate capacitors has significantly decreased.
PPC or Polypropylene Capacitor:

In this types of capacitors, the tolerance level required is higher than what the polyester capacitor can provide, then the polypropylene capacitors are used in these cases.
The material used for the dielectric in the polypropylene capacitor is a polypropylene film.
The advantage which the polypropylene capacitor has over the other capacitors is that it can withstand very high voltage across a time period and thereby the change in the capacitance level due to the increase and decrease of voltage over a time period is very low.
The polypropylene capacitor is also used in cases where the frequency being used is very low, mostly in the range of 100kHz being the maximum limit. The general availability of the polypropylene capacitor is in the form of leaded electronics components.
Glass Capacitors:
The dielectric which is used in the glass capacitor is made up of glass. Even though the glass capacitors are expensive, their performance levels are very high.
The RF current capability of the glass capacitors is very high along with the loss being extremely low. Additionally, there is absence of any piezo-electric noise in the glass capacitors.
All these and some additional properties of the glass capacitors make them most appropriate and ideal for RF applications which require high performance.
Supercap:

The other names by which the supercap is known are ultracapacitor or supercapacitor.
The capacitance values of these capacitors are very large as such is their name. The capacitance levels of the ultracapacitor go nearly towards many thousand Farads.
The ultracapacitor is used in the industry for providing a supply of memory hold-up along with various uses within the realm of automotive applications. The different major types of the capacitors are included under the supercap.
Along with them, there are various other capacitor types of capacitors which are used when the applications are specialized in nature.
The identification of the capacitors is majorly done through their parameters such as values which are marked over the cases of the capacitors. In order to display the parameters in a manner which is compact, the markings of the parameters are done in the form of a code.
Available link for download
Labels:
capacitors,
explained,
of,
types
Subscribe to:
Posts (Atom)